地磅加減器內的傳感器、主線、接線盒都可以安裝加減器,簡單來說就是利用無線射頻技術加減重量,遠程改變地磅顯示器的結果
產地 | 國產 | 加工定制 | 否 |
---|
地磅加減器內的傳感器、主線、接線盒都可以安裝加減器,簡單來說就是利用無線射頻技術加減重量,遠程改變地磅顯示器的結果
性能特點:
1、雙向調節,可加可減,可精確調節噸位、公斤。
2、無線遙控,智能解密,性能穩定,效果可靠。
3、體積小巧可隨身攜帶,使用方便、隱蔽、安全,單手即可操作。
4、遙控器對地秤不會產生任何負影響,不按就不會改變原來的數值。
5、操作距離遠,在200米以內有用,信號可穿墻或其它障礙物。
6、使用壽命長達5年以上。
7、該產品可防電子攔截、電子干擾。
8、適用于各類模擬數字電子衡器,如電子磅、電子稱、皮帶稱、電子天平等。
地磅加減器安裝非常簡單,但也要注意以下幾點:
Loadometer remote installation is very simple, but also should pay attention to the following points:
1.安裝拆卸地磅的遙控器之前,都應該關掉電源,防止整個線路不暢通的情況給領受器芯片通電,電壓不穩都可能直接燒壞芯片.就比如我們的手電機池拆卸之前先關機一樣。
1. before installation and disassembly of remote control, should turn off the power, to prevent the line does not flow to the receiver chip power, voltage instability can be directly burnt like chips. Before we remove the first electric machine pool off the same.
2.如果在通電的情況下安裝,接線則先接信號線,再接電源線;如圖先接綠白,后接黑紅。外置對插則先連接傳感器端,電子遙控器再接儀表端。如圖:按順序接。
2. if in the case of electricity installation, wiring is first connected to the signal line, then the power line; figure first green and white, with black and red. The external plug is connected to the sensor and the electronic remote is then connected to the instrument terminal. As shown: in order.
3.內置對插芯片則要認清板子上的儀表端和傳感器端,有中文標記,不要插反了,而且在儀表里面拔插頭要小心點,不要把插頭指針搞斷了。
3. built-in plug-in chip, you should recognize the dashboard on the end of the instrument and sensor side, there are Chinese markers, do not plug in, and in the instrument to unplug the plug to be careful, do not plug the needle to break.
4.安裝好后儀表開機,等待儀表歸零后,按一下遙控8號鍵,儀表仍是0便可以進入調試狀態了。大家永遠要記住的是,按8號鍵必須歸零。
4. after installation of instrument boot, wait for instrument zero, press the remote control button 8, the instrument is still 0 can enter the debug state. We will always remember, press the button 8 to zero.
杰出的安裝使用習慣也可有效延長地磅的遙控器的使用壽命,遇到任何不懂的地方。
Good habits are the installation can effectively prolong the service life of the remote control, do not know where any.